• RJ-45 port for electrical 10/100/1000M Ethernet
• SFP port for OC-3/12/48 or STM-1/4/16 and Fibre Channel 1x, 2x, 4x or 100/1000M Ethernet
• SFP+ port for OC-192, STM-64, 10 GigE LAN/WAN or Fibre Channel 8x, 10x
• RJ-48C and bantam port for DS1 or E1
• BNC port for DS3 or E1/E3/E4 or STS-1e/STS-3e or STM-0e/STM-1e
  • DS1/DS3 and E1/E3/E4 testing
  • OC-3/12/48/192 and STM-1/4/16/64 BER testing with configurable threshold settings
  • Coupled, Decoupled and Through mode testing
  • Error and alarm insertion and monitoring
  • Overhead monitoring and manipulation
  • High-order and low-order mappings
  • Tandem connection monitoring (TCM)
  • Pointer manipulation, including pointer sequence testing as per Telcordia GR-253, ANSI T1.105-03 and ITU G.783
  • Performance monitoring as per G.821, G.826, G.828, G.829, M.2100, M.2101
  • Frequency analysis and offset generation
  • Automatic protection switching
  • Service-disruption time measurements
  • Round-trip delay measurements
  • Dual DS1/DS3 receiver (Rx) support
  • DS1 loop codes and NI/CSU emulation
  • DS1/DS3 autodetection of line code, framing and pattern
  • DS1 FDL and DS3 FEAC
  • Fractional T1/E1 testing
  • External clock sync support
  • 10 Base-T to 10 GigE testing
  • EtherSAM (ITU-T Y.1564) (bidirectional)
  • RFC 2544 (bidirectional)
  • Traffic generation and monitoring
  • Through mode
  • Intelligent autodiscovery
  • IPv6 testing
  • Ping/Traceroute
  • Cable testing
  • Dual Test Set mode
  • Smart loopback
  • Fibre Channel 1x, 2x, 4x, 8x, 10x

Setting a New GUI Standard: Unprecedented Simplicity in Configuration Setup and Navigation

The FTB-880 NetBlazer’s intelligent situational configuration setup feature guides technicians through complete, accurate testing processes (suggestion prompts, help guides, etc.). It reduces navigation by combining associated testing functions on a single screen, and offers intelligent autodiscovery that allows a single technician to perform end-to-end testing.

Dedicated Quick-Action Buttons

• Remote discovery to find all the other EXFO units
• Laser on/off
• Test reset to clear the results and statistics while running a test
• Report generation
• Save or load test configurations
• Quick error injection

Assorted Notifications

• Clear indication of link status for single or dual ports
• Negotiated speed display for single or dual ports
• Power status available at all times for single or dual ports
• Pass/fail indication at all times
• Pattern and clock synchronization
• Frequency offset with valid-range color indicator
• Overhead overwrite indicator
• Error/alarm injection
• Alarm hierarchy pinpointing the root-cause (when possible)

Streamlined Navigation

• Remote discovery button available at all times; no reason to leave your current location to scan for a remote unit
• Testing status can be maximized to fill the entire screen by simply clicking on the alarm status button; whether the unit is in your hand or across the room, test results can be easily determined with a simple glance at the display screen
• RFC 2544 configuration is maximized in a single page; no need to navigate through multiple screens to configure individual subtests
• RFC 2544 results and graphs are also maximized in a single page; no need to navigate through multiple screens to view individual RFC subtest results
• Simplified test structure definition using task-based test application selection, signal configuration front end and smart timeslot selection
• Centralized functions: error/alarm management, performance monitoring and overhead manipulation/monitoring

Key DSn/PDH and SONET/SDH Features

Simplified BER Testing

The FTB-880 NetBlazer provides the ability to pre-configure bit-error-rate (BER) thresholds that are user-defined prior to running the test. This allows for a simple pass/fail verdict at the conclusion of the test, leaving no room for misinterpretation of the test results.

Decoupled Mode

The Decoupled mode enables the user to independently configure the Tx and Rx ports of the FTB-880 NetBlazer module. This allows to test the mapping and demapping functionality of a network element or at cross-connect points in the network.

Through Mode

This mode is required for in-service monitoring of the network. The FTB-880 NetBlazer can be inserted in-line on a specific link, and can then monitor and analyze the errors and alarms on that link while remaining non-intrusive.

Simplified Error Injection

This FTB-880 feature enables the user to inject errors with a single click, from any screen, allowing technicians to ensure circuit continuity prior to starting a test. Furthermore, the error injection functionality can be pre-programmed for any given type of error, and not just for bit errors.

Complete Overhead Monitoring

The FTB-880 NetBlazer offers access to the entire SONET/SDH overhead (OH) bytes from a single page. Furthermore, by selecting any given OH byte, the user can retrieve additional detailed information about that byte without having to switch pages.

Key Features

Intelligent Network Discovery Mode

Using the FTB-880 or the FTB-860x test set, you can single-handedly scan the network and connect to any available EXFO datacom remote tester. Simply select the unit to be tested and choose whether you want traffic to be looped back via Smart Loopback or Dual Test Set for simultaneous bidirectional EtherSAM and RFC 2544 results. No more need for an additional technician at the far end to relay critical information—the NetBlazer products take care of it all.

Smart Loopback Flexibility

The Smart Loopback functionality has been enhanced to offer five distinct loopback modes. Whether you are looking to pinpoint loopback traffic from a UDP or TCP layer, or all the way down to a completely promiscuous mode (Transparent Loopback mode), that FTB-880 or the FTB-860x NetBlazer has the flexibility to adjust for all unique loopback situations.

Global Pass/Fail Analysis

The NetBlazer series provides real-time pass/fail status via text or icons. Clicking on the pass/fail indicator maximizes this important status to full screen, providing instant, easily understood notification whether the unit is in the technician’s hands or across the room.

VLAN/MPLS

Today's networks are expected to deliver high performance. To match such high expectations, service providers must rely on various mechanisms such as Ethernet tagging, encapsulation and labeling. Thanks to these additions, service providers can enhance security, scalability, reliability and performance. The NetBlazer series supports virtual local area network (VLAN) tags, Q-in-Q VLAN tags and multiprotocol label switching (MPLS).

EtherSAM: The New Standard in Ethernet Testing

Until now, RFC 2544 has been the most widely used Ethernet testing methodology. However it was designed for network device testing in the lab, not for service testing in the field. ITU-T Y.1564 is the new standard for turning up and troubleshooting Carrier Ethernet services. It has a number of advantages over RFC 2544, including validation of critical SLA criteria such as packet jitter and QoS measurements.This methodology is also significantly faster, therefore saving time and resources while optimizing QoS.

EXFO’s EtherSAM test suite—based on the ITU-T Y.1564 Ethernet service activation methodology—provides comprehensive field testing for mobile backhaul and commercial services.

Contrary to other methodologies, EtherSAM supports new multiservice offerings. It can simulate all types of services that will run on the network and simultaneously qualify all key SLA parameters for each of these services. Moreover, it validates the QoS mechanisms provisioned in the network to prioritize the different service types, resulting in better troubleshooting, more accurate validation and much faster deployment. EtherSAM is comprised of two phases, the service configuration test and the service performance test.

Service Configuration Test

Service Performance Test

EtherSAM Bidirectional Results

EXFO’s EtherSAM approach proves even more powerful as it executes the complete ITU-T Y.1564 test with bidirectional measurements. Key SLA parameters are measured independently in each test direction, thus providing 100 % first-time-right service activation—the highest level of confidence in service testing.

Efficiently Assessing Performance of Fibre Channel Services

The NetBlazer Series modules provide comprehensive testing capabilities for Fibre Channel network deployments, supporting multiple Fibre Channel interfaces.

Applications

Since most storage area networks (SANs) cover large distances and Fibre Channel has stringent performance requirements, it is imperative to test at each phase of network deployment to ensure appropriate service levels. EXFO’s NetBlazer series modules provide full wire speed traffic generation at the FC-2 layer, which allows BER testing for link integrity measurements. In addition, latency, buffer to buffer credit measurements for optimization as well as login capabilities are supported.

Latency

Transmission of frames in a network is not instantaneous and is subject to multiple delays caused by the propagation delay in the fiber and by processing time inside each piece of network equipment. Latency is the total accumulation of delays between two end points. Some applications such as VoIP, video and storage area networks are very sensitive to excess latency.

It is therefore critical for service providers to properly characterize network latency when offering Fibre Channel services. From the latency measurement that they perform, the NetBlazer series modules can estimate buffer-to-buffer credit value requirements.

Buffer-to-Buffer Credit Estimation

In order to regulate traffic flow and congestion, Fibre Channel ports use “buffers” to temporarily store frames. The number of frames a port can store is referred to as a “buffer credit”. Each time a frame is received by a port, an acknowledgement frame is sent. The buffer-to-buffer credit threshold refers to the amount of frames a port can transmit without receiving a single acknowledgement.

This is a crucial configuration parameter for optimal network performance. Usually, network administrators calculate the value by taking the traveled distance and the data rate into consideration; however, since latency issues are not considered, poor accuracy is to be expected. The NetBlazer series modules are capable of estimating buffer credit values with respect to latency by calculating the distance according to the round-trip latency time. This value can then be used by network administrators to optimize the network configuration.

Login Testing

Most new-generation transport devices (xWDM or SONET/SDH mux) supporting Fibre Channel are no longer fully transparent; they also have increased built-in intelligence, acting more as Fibre Channel switches. With switch fabric login ability, the NetBlazer series modules support connections to a remote location through a fabric or semi-transparent networks.

The login process not only permits the unit to connect through a fabric, but it also exchanges some of the basic port characteristics (such as buffer-to-buffer credit and class of service) in order to efficiently transport the traffic through the network.

The login feature allows automatic detection of port/fabric login, login status (successful login, in progress, failure and logout) and response to remote buffer-to-buffer advertised credit.

EXFO Connect

EXFO Connect pushes and stores test equipment and test data content automatically in the cloud, allowing you to streamline test operation from build-out to maintenance.

EXpert Test Tools

EXpert Test Tools is a series of platform-based software testing tools that enhance the value of the FTB-1 platform, providing additional testing capabilities without the need for additional modules or units.

• The EXpert VoIP Test Tools generates a voice-over-IP call directly from the test platform to validate performance during service turn-up and troubleshooting.
  • Supports a wide range of signaling protocols, including SIP, SCCP, H.248/Megaco and H.323
  • Supports MOS and R-factor quality metrics
  • Simplifies testing with configurable pass/fail thresholds and RTP metrics
• The EXpert IP Test Tools integrates six commonly used datacom test tools into one platform-based application to ensure field technicians are prepared for a wide-range of testing needs.
  • Rapidly perform debugging sequences with VLAN scan and LAN discovery
  • Validate end-to-end ping and traceroute
  • Verify FTP performance and HTTP availability
• This powerful IPTV qality assessment solution enables set-top-box emulation and passive monitoring of IPTV streams, allowing quick adn easy pass/fail verification of IPTV installations.
  • Real-time video preview
  • Analyzes up to 10 video streams
  • Comprehensive QoS and QoE metrics including MOS score